About Irwin

Description

What's Holding Back The Fiat 500 Replacement Key Cost Industry?
Fiat 500 Replacement Key Fob

If your remote key fob isn't working, it may be time to replace the battery. If you do replace the battery and it continues to stop working, then the problem could be elsewhere.

At United Locksmith, we specialize in making new keys for classic automobiles. We have all of the tools and accessories needed for this service.

Dead Coin Battery

The most common reason your Fiat 500 key fob will not unlock or lock the doors is a dead battery. The key fob is equipped with the battery of a coin-cell which will quickly drain when it isn't being utilized frequently enough. If your remote began to show signs of weakening such as a loss of range and then completely stopped working The battery is probably dead.

The battery inside the key fob is held in place with metal retaining clips. If the clips are loose, it can cause problems with contact, which can prevent the remote from receiving power. Use a flathead screwdriver pry open the retaining clip and remove the old battery. Make sure you use an identical replacement battery type of voltage, dimensions and specifications as the original battery.

Water exposure can cause the key fob to corrode, or even become damaged. Even a small bath in soapy, warm water can damage the chip. Make sure your key fob is dry.

Water Damage

Water damage could be the cause of your key fob not working properly. Key fobs are fitted with rubber seals that protect them from being damaged by light rain or splashes of water. However, it is vital to keep your keys out of the pool, ocean, and washing machine!

The key fob has an electronic chip that sends an alert to the immobilizer of your car. This is what allows your 500 to start or lock, but in the event that the chip becomes saturated, it won't be able to longer function.

You can try cleaning the inside electronics of your keyfob using isopropyl alcohol, or an electronic cleaner to determine whether they're still working. However, it's best to get a replacement from a dealer instead of trying to repair the key fob that has been submerged in salt water.

A replacement fob can cost you a little bit, but it's a lot cheaper than having to have your Fiat 500 towed to a dealership and fixed there! You can also do it yourself by following some simple steps. Just make sure you have the right battery type before you attempt to open your key fob. You can find step-by-step instructions for any car keyfob online.

Faulty Chip

The chip in the key fob communicates to your car's immobiliser system to ensure the car is able to start when the correct key is used. If the chip is damaged or damaged it won't allow your car to start no matter what you do.


Damage to the water or a dead battery are the most frequently cited reasons for defective chips. It is recommended to leave the job to a professional locksmith, who will be able to replace the chip quickly and at an affordable price.

If your key fob fails to function after exposure to clean tap water or rain, take out the battery and wipe down the electronic component using a paper towel to ensure it's completely dry before putting it back into. If the key fob isn't working, it is likely to be a damaged chip and must be replaced.

A few people will visit their dealer in order to get a new Fiat fob. However, this could be a costly option. United Locksmith is the best option for you if need your Fiat key fob repaired at a reasonable cost. We have the tools and knowledge necessary to fix your Fiat key fob in a timely and professional way.

Faulty Receiver Module

Fiat key fobs send a signal to the vehicle, which will unlock and lock doors (and start the car for those with an automatic transmission) up to 50 feet. However there are a few factors that could cause the fob to cease working. It could be due to a dead battery damaged by water or worn buttons or a problem with the receiver module and signal interference, or an electronic chip malfunctioning.

If the fob was placed in the pocket of someone who has suffered extreme trauma (such as being dropped onto the hard floor or washed in the washing machine) the fob might not be in a position to communicate with the Body Control Module (BCM) of the vehicle. This is because the BCM is a secure system that can only accept signals from a genuine original key and not another.

You'll have to replace the fob in case this happens. A professional locksmith can take care of all aspects of the replacement procedure as well as programming a new one for the 500. keyless entry can even provide you with the fob cloned to work just like the original (and costs only less than what it would cost).